Lada priora
The cost of a halogen low beam lamp is 250–460 rubles, and a high beam is 100–350 rubles. The cost of a halogen low beam lamp is 250–460 rubles, and a high beam is 100–350 rubles. The cost of a halogen low beam lamp is 250–460 rubles, and a high beam is 100–350 rubles.
Replacing bulbs in the headlamp
All manipulations for replacing the lamps are shown on the left headlight (in the photo it is removed for greater clarity), on the right side the work is carried out similarly. The only difference is that replacing the lamps in the left headlamp will be more convenient with the battery removed.
one
To replace the low beam lamp, remove the rubber cover located closer to the wing of the car. To replace the low beam lamp, remove the rubber cover located closer to the wing of the car. To replace the low beam lamp, remove the rubber cover located closer to the wing of the car.
2
Disconnect the block of wires from the lamp. Disconnect the block of wires from the lamp. Disconnect the block of wires from the lamp.
3
Push down on the spring clip of the lamp, disengage it from the hooks of the reflector. Push down on the spring clip of the lamp, disengage it from the hooks of the reflector. Push down on the spring clip of the lamp, disengage it from the hooks of the reflector.
four
We take out the low beam lamp from the headlamp housing. Install the new H7 headlight lamp in the reverse order. We take out the low beam lamp from the headlamp housing. Install the new H7 headlight lamp in the reverse order. We take out the low beam lamp from the headlamp housing. Install the new H7 headlight lamp in the reverse order.
five
To replace the high-beam lamp, remove the protective rubber cover from the body of the headlamp. To replace the high-beam lamp, remove the protective rubber cover from the body of the headlamp. To replace the high-beam lamp, remove the protective rubber cover from the body of the headlamp.
On a note
High and low beam lamps are halogen. When replacing them, do not touch the flasks with your fingers, as grease stains can cause local darkening of the glass. Work in clean gloves. If you still accidentally touch the lamp with your fingers, wipe it with a clean rag soaked in alcohol. Remember: over time, the lamps gradually become cloudy, which leads to a loss of light output. Therefore, if you want to feel confident on the night road, make it a rule to regularly change the headlight lamps, without waiting for one of them to burn out.
6
Disconnect the block of wire from the lamp. Disconnect the block of wire from the lamp. Disconnect the block of wire from the lamp.
7
Having opened the ends of the spring clip, we disengage them from the hooks of the reflector and we remove the clip from the lamp. Having opened the ends of the spring clip, we disengage them from the hooks of the reflector and we remove the clip from the lamp. Having opened the ends of the spring clip, we disengage them from the hooks of the reflector and we remove the clip from the lamp.
eight
We take out the main beam lamp from the headlamp housing. Install the new high beam lamp H1 in the reverse order. We take out the main beam lamp from the headlamp housing. Install the new high beam lamp H1 in the reverse order. We take out the main beam lamp from the headlamp housing. Install the new high beam lamp H1 in the reverse order.
9
To replace the side light bulb in the headlamp, we take out the cartridge with the lamp. To replace the side light bulb in the headlamp, we take out the cartridge with the lamp. To replace the side light bulb in the headlamp, we take out the cartridge with the lamp.
ten
We take out the lamp from the cartridge. Install the new W5W side light bulb in the reverse order. We take out the lamp from the cartridge. Install the new W5W side light bulb in the reverse order. We take out the lamp from the cartridge. Install the new W5W side light bulb in the reverse order.
eleven
To replace the indicator lamp with a Phillips screwdriver, unscrew the three screws A and the self-tapping screw B securing the headlight's decorative trim and remove it. To replace the indicator lamp with a Phillips screwdriver, unscrew the three screws A and the self-tapping screw B securing the headlight's decorative trim and remove it. To replace the indicator lamp with a Phillips screwdriver, unscrew the three screws A and the self-tapping screw B securing the headlight's decorative trim and remove it.
12
We rotate the indicator lamp bulb counterclockwise (for clarity, shown on the removed headlamp) … Turn the lamp indicator bulb counterclockwise (for clarity, shown on the removed headlamp) … Turn the lamp holder of the indicator bar counterclockwise (for clarity on the removed headlight) …
13
… and take it out of the headlamp housing. … and take it out of the headlamp housing. … and take it out of the headlamp housing.
14
Having pressed a lamp, we turn it against the stop counterclockwise and we take out of a cartridge. Install the new direction indicator lamp PY21W in the reverse order. Having pressed a lamp, we turn it against the stop counterclockwise and we take out of a cartridge. Install the new direction indicator lamp PY21W in the reverse order. Having pressed a lamp, we turn it against the stop counterclockwise and we take out of a cartridge. Install the new direction indicator lamp PY21W in the reverse order.
Headlight Removal
We remove the headlamp for replacement or for body repair. Work is shown on the left headlamp; the right one is removed similarly. Disconnect the wire terminal from the negative terminal of the battery. Remove the front bumper.
one
Pressing the screwdriver blade onto the clip of the wiring harness pad … Pressing the screwdriver blade onto the clip of the wiring harness pad … Pressing the screwdriver blade onto the clip of the wiring harness pad …
2
… disconnect the block from the connector on the headlamp housing. … disconnect the block from the connector on the headlamp housing. … disconnect the block from the connector on the headlamp housing.
3
With the “8” head, we unscrew the bolt of the upper mounting of the headlamp. With the “8” head, we unscrew the bolt of the upper mounting of the headlamp. With the “8” head, we unscrew the bolt of the upper mounting of the headlamp.
four
With the same tool, we unscrew the bolt of the lower fastening of the headlamp, and with a Phillips screwdriver - a self-tapping screw (shown by arrow). With the same tool, we unscrew the bolt of the lower fastening of the headlamp, and with a Phillips screwdriver - a self-tapping screw (shown by arrow). With the same tool, we unscrew the bolt of the lower fastening of the headlamp, and with a Phillips screwdriver - a self-tapping screw (shown by arrow).
