The “norm” package includes the so-called audio preparation, that is, pads with summed wire harnesses for connecting the head unit and speakers in the doors. The hardest part is to make everything beautiful.
Components

Head unit MMD-3503S - 4, 500 rubles. MJ520 5.25 speaker system - 540 rubles. Active MANT6 antenna - 980 rubles. MMD-3503S head unit - 4500 rubles. MJ520 5.25 speaker system - 540 rubles. Active antenna MANT6 - 980 rubles.
Head device
For work, you will need the simplest tools: straight and Phillips screwdrivers, clerical knife … "Consumables" at this stage so far requires only one - an insulating tape.
one

Attention! Before starting work, you must disconnect the power supply by removing the terminals from the battery. Attention! Before starting work, you must disconnect the power supply by removing the terminals from the battery.
2

Install the antenna in the upper corner of the windshield. We’ll lay out the wiring for the dash, dismantling the glove compartment. Install the antenna in the upper corner of the windshield. We’ll lay out the wiring for the dash, dismantling the glove compartment.
3

From the right pillar of the windshield we remove the plastic trim (attached to the latches) and go up. From the right pillar of the windshield we remove the plastic trim (attached to the latches) and go up.
four

The active Mystery antenna is self-adhesive. Before decal it is necessary to clean and degrease the glass. The active Mystery antenna is self-adhesive. Before decal it is necessary to clean and degrease the glass.
five

Antenna antennae are mounted on double-sided tape. Now the rack overlay can be put in place. Antenna antennae are mounted on double-sided tape. Now the rack overlay can be put in place.
6

To install the head unit, you need to dismantle the plastic container and disconnect the "chips". To install the head unit, you need to dismantle the plastic container and disconnect the "chips".
7

We install the metal holder of the PG, we connect the power, antenna and speakers according to the scheme. We install the metal holder of the PG, we connect the power, antenna and speakers according to the scheme.
eight

Before installing the GU in its nest, it is worth testing its performance. Before installing the GU in its nest, it is worth testing its performance.
Acustic systems
In addition to the previous set of tools, prepare a drill or a screwdriver with a “crown” or a conical drill, an electric jigsaw, a marker or a carpenter's pencil. This may be enough, but for the installation of speaker grilles we also took plastic glue and masking tape. When carrying out these works, accuracy is required.
one

The speaker installation kit includes the speakers themselves, their grilles, wiring, mounting brackets and screws. The speaker installation kit includes the speakers themselves, their grilles, wiring, mounting brackets and screws.
2

The main tool for removing door trim is a large Phillips screwdriver. Each skin is fastened with five screws. The main tool for removing door trim is a large Phillips screwdriver. Each skin is fastened with five screws.
3

The door lock button is simply twisted, after which the lining must be carefully lifted, being careful not to damage the plastic caps. The door lock button is simply twisted, after which the lining must be carefully lifted, being careful not to damage the plastic caps.
four

On the reverse side of the casing is a power window connector. To disconnect it, just open the latches and easily pull the button. On the reverse side of the casing is a power window connector. To disconnect it, just open the latches and easily pull the button.
five

Now the door trim can be completely removed and temporarily set aside. It will be needed only after installing the speakers. Now the door trim can be completely removed and temporarily set aside. It will be needed only after installing the speakers.
6

The door already has space for attaching 13-cm speakers. Their installation is simple: we connect the terminals, put the brackets … The door already has places for fastening 13-centimeter speakers. Their installation is simple: we connect the terminals, put the brackets …
7

… and screw in the screws. The speakers can also be screwed to the plastic door trim, but in this case they will rattle and protrude strongly. … and screw in the screws. The speakers can also be screwed to the plastic door trim, but in this case they will rattle and protrude strongly.
eight

It is convenient to use a carpenter's pencil to mark the holes for the speakers. It is better than a marker in that if an error occurs, the line is easy to erase. It is convenient to use a carpenter's pencil to mark the holes for the speakers. It is better than a marker in that if an error occurs, the line is easy to erase.
9

It is better to drill a hole for a jigsaw file from the "wrong" side of the casing: it is not so scary if the drill slips. It is better to drill a hole for a jigsaw file from the "wrong" side of the casing: it is not so scary if the drill slips.
ten

When working with a jigsaw, be careful - here you have no right to make a mistake. For a neat cut, it is better to use a file with small cloves. When working with a jigsaw, be careful - here you have no right to make a mistake. For a neat cut, it is better to use a file with small cloves.
eleven

The edging of the grilles is usually attached to the screws, we put them on the glue - so aesthetically pleasing. Until the glue has dried, they fixed it with masking tape. The edging of the grilles is usually attached to the screws, we put them on the glue - so aesthetically pleasing. Until the glue has dried, they fixed it with masking tape.
12

And here are the speakers in their places, attached to the metal doors. Decorative grilles were additionally fixed with black sealant to prevent rattling. Now our Granta is with music! And here are the speakers in their places, attached to the metal doors. Decorative grilles were additionally fixed with black sealant to prevent rattling. Now our Granta is with music!
On a note
At the forum of the official club of owners of Lada Granta, they asked why the jigsaw for cutting holes was not included in the vehicle equipment. Representatives of AvtoVAZ referred to the low cost of the car, the ease of operation and the equipment of the service station. But the problem is solved by elementary perforation in the casing instead of a fake "mesh"!