Chevrolet niva
An air filter costs 150–250 rubles, a cabin filter costs 160–270 rubles, and a fuel filter costs 180–250 rubles. An air filter costs 150–250 rubles, a cabin filter costs 160–270 rubles, and a fuel filter costs 180–250 rubles.
Replacing the air filter element
The replaceable air filter element needs to be replaced every 30 thousand kilometers. When operating a car in a dusty area, the interval should be reduced by 1.5–2 times. If the filter is deformed or damaged, change it immediately. A heavily soiled element can lead to increased wear and engine power.
one
Using a Phillips screwdriver, unscrew the four screws that secure the filter cover. Using a Phillips screwdriver, unscrew the four screws that secure the filter cover.
2
Lift the lid … Lift the lid …
3
… and take out the filter element of the air filter. We clean the cavities of the housing and the cover of the air filter and install a new element in the reverse order. … and take out the filter element of the air filter. We clean the cavities of the housing and the cover of the air filter and install a new element in the reverse order.
four
The corrugations of the filter element during installation should be parallel to the arrow on the air duct inside the filter housing. We install the filter cover and wrap the mounting screws. The corrugations of the filter element during installation should be parallel to the arrow on the air duct inside the filter housing. We install the filter cover and wrap the mounting screws.
Cabin Filter Replacement
We replace the replacement element of the filter for cleaning the external air in accordance with the maintenance schedule every 15 thousand kilometers.
This filter is located under the windshield lining on the right side. Above it, in the glass lining, a cover is installed on the sealant, which is fixed by a self-tapping screw.
one
Use a Phillips screwdriver to unscrew the screw that secures the filter cover. Use a Phillips screwdriver to unscrew the screw that secures the filter cover.
2
Remove the cover. Remove the cover.
3
Prying off with a screwdriver … Prying off with a screwdriver …
four
… remove the replaceable element from the filter housing. When installing a new element, we orient it so that the foam stuck to it is located on top. Before installing the cover, apply sealant along its contour. … remove the replaceable element from the filter housing. When installing a new element, we orient it so that the foam stuck to it is located on top. Before installing the cover, apply sealant along its contour.
Replacing the fuel filter
The fuel filter is installed at the bottom of the car, in front of the right rear wheel, and is closed by a plastic casing. We carry out work on a viewing ditch or overpass. The fuel in the power system (with the ignition on and some time after it is turned off) is under pressure. Therefore, if we replace the filter immediately after the trip or after turning on the ignition, it is necessary to relieve the fuel pressure in the power supply system.
If the ignition is not turned on for a day or more, the fuel pressure in the system, as a rule, is absent. This can be checked by unscrewing the cap of the fuel rail fitting and pressing the spool pin.
To relieve system pressure …
one
… set the right rear seat cushion upright. We bend sound insulation. … set the right rear seat cushion upright. We bend sound insulation.
2
Using a Phillips-head screwdriver, we turn off two self-tapping screws of the hatch cover fastening … We use a Phillips-head screwdriver to turn off two self-tapping screws of the hatch cover fastening …
3
… and remove the cover. … and remove the cover.
four
Having squeezed out a block lock, we disconnect a block of wires from the fuel module. We start the engine and let it idle to a stop due to fuel exhaustion. Then we turn on the starter for 2-3 s. After that, the pressure in the fuel system will be relieved. Having squeezed out a block lock, we disconnect a block of wires from the fuel module. We start the engine and let it idle to a stop due to fuel exhaustion. Then we turn on the starter for 2-3 s. After that, the pressure in the fuel system will be relieved.
five
Using the “10” wrench, unscrew the bolt and two casing fastening nuts. Using the “10” wrench, unscrew the bolt and two casing fastening nuts.
6
Remove the fuel filter cover. Remove the fuel filter cover.
7
Having squeezed two clamps of the tip of the outlet fuel pipe, remove the tip from the filter fitting. Having squeezed two clamps of the tip of the outlet fuel pipe, remove the tip from the filter fitting.
On a note
In accordance with the maintenance regulations, the fuel filter must be replaced every 30 thousand kilometers. The interval should be shortened if the car is operated in dusty conditions or with low fuel quality.
When working with elements of the fuel system, do not forget about fire safety measures! Do not smoke, do not approach an open fire machine. Do not change the filter in rooms with natural gas appliances.
eight
Using the “10” key, weaken the tightening of the bolt of the filter mounting clamp. Using the “10” key, weaken the tightening of the bolt of the filter mounting clamp.
9
Having squeezed two clamps of the tip of the conductive fuel tube, we shift the filter, removing its fitting from the tip of the tube and remove the fuel filter from the clamp. Since fuel remains in the filter, we pour it into a previously prepared container. Install the new filter in the reverse order. Having squeezed two clamps of the tip of the conductive fuel tube, we shift the filter, removing its fitting from the tip of the tube and remove the fuel filter from the clamp. Since fuel remains in the filter, we pour it into a previously prepared container. Install the new filter in the reverse order.
