Chevrolet lacetti
The original air filter costs 430-470 rubles., Cabin - 310-350 rubles., Fuel - 340-400 rubles. The original air filter costs 430-470 rubles., Cabin - 310-350 rubles., Fuel - 340-400 rubles.
REPLACING THE SALON FILTER
The usual lifetime of a cabin filter is 15 thousand kilometers. As in the case with the engine air filter, the interval measured by the regulation should be reduced by 1.5–2 times for frequent trips on dusty roads. A deformed or damaged element must be replaced regardless of mileage.
The filter cover is located in the passenger compartment behind the glove compartment above the legs of the front passenger. It is more convenient to replace the filter with the glove box removed.
one
Using the “7” key (head) or a Phillips screwdriver, we turn off the four screws of the filter cover fastening… “7” key (head) or a Phillips screwdriver turn off the four screws of the filter cover fastening …
2
… and remove the cover from the air conditioning system. … and remove the cover from the air conditioning system.
3
Pull the filter out of the air conditioner housing all the way into the carpeted floor … Pull the filter out of the air conditioning system all the way into the carpeted floor …
four
… and we add the filter according to the technological sections of its frame (for clarity, it is shown on the removed filter). … and we add the filter according to the technological sections of its frame (for clarity, it is shown on the removed filter).
five
We completely remove the filter from the air conditioner housing. Install the new filter in the reverse order. We completely remove the filter from the air conditioner housing. Install the new filter in the reverse order.
REPLACING THE AIR FILTER REPLACEMENT ELEMENT
The replaceable air filter element needs to be replaced every 45 thousand kilometers. When operating a car in a dusty area, the interval should be reduced by 1.5–2 times. If the filter is deformed or damaged, change it immediately. A heavily soiled element can lead to increased wear and engine power.
one
The “8” head unscrews the four screws that secure the air filter housing cover. The “8” head unscrews the four screws that secure the air filter housing cover.
2
Lift the lid … Lift the lid …
3
… and take out the filter element of the air filter. … and take out the filter element of the air filter.
We clean the cavities of the housing and the cover of the air filter and install a new element in the reverse order.
REPLACING THE FUEL FILTER
The fuel filter is located under the underbody, right in front of the fuel tank. When starting to replace the filter, the first step is to relieve the fuel pressure.
one
To do this, with the ignition off, remove the fuel pump fuse (Ef18) from the mounting block in the engine compartment. We start the engine and let it idle to a stop due to the generation of fuel in the system. Then we turn on the starter for 2-3 seconds. As a result, the pressure in the fuel system will be relieved. To do this, with the ignition off, remove the fuel pump fuse (Ef18) from the mounting block in the engine compartment. We start the engine and let it idle to a stop due to the generation of fuel in the system. Then we turn on the starter for 2-3 seconds. As a result, the pressure in the fuel system will be relieved.
2
Disconnect the ground wire from the terminal on the fuel filter housing. Disconnect the ground wire from the terminal on the fuel filter housing.
3
Using a key or a “10” head, we unscrew the coupling bolt of the mounting clamp. Using a key or a “10” head, we unscrew the coupling bolt of the mounting clamp.
four
Remove the wire. Remove the wire.
five
Remove the protective cover. Remove the protective cover.
6
With the end of a screwdriver, push the lock out of the tip of the fuel pipe … The end of the screwdriver push out the lock out of the tip of the fuel pipe …
7
… and remove the tip of the white tube. … and remove the tip of the white tube.
eight
Squeezing the antennae of the plastic retainer of the tip of the fuel tube … Squeezing the antennae of the plastic retainer of the tip of the fuel tube …
9
… and remove the tip of the black tube from the filter fitting. … and remove the tip of the black tube from the filter fitting.
ten
We remove the fuel filter from the bracket. We remove the fuel filter from the bracket.
Install the filter in the reverse order.
The tips of the fuel pipes are put on the filter fittings until the clips snap into place.
After installing the fuel pump fuse, turn on the ignition and check the tightness of the connections.
On a note
In accordance with the maintenance regulations, the fuel filter must be replaced every 45 thousand kilometers.
Frequent gas stations of poor quality. An active gravel drive can completely disable the filter.
When working with elements of the fuel system, do not forget about fire safety measures! Do not smoke. Do not get near an open fire. Do not change the filter in rooms that have natural gas appliances and are equipped with a pilot torch (water heater, clothes dryer).
Recommendation: extend the life of the air conditioner
Many drivers, having believed in the absolute reliability of an automobile air conditioner, completely forget about its regular maintenance and diagnostics. And in vain, it could end in expensive repairs. Diagnosis of the air conditioner must be carried out at least once a year before the active season, that is, after the end of winter. The list of the most frequently identified problems: corrosion and mechanical damage to the condenser, to which all external adversities are pouring (anti-icing reagents, dirt, small stones), bearing failure in the compressor pulley (if tightened with a replacement, then the electromagnetic coupling and compressor pressure plate will fly), through corrosion on pipelines, leaky joints. In the event of a depressurization of the system, it is possible that it will be necessary to replace the receiver-dryer.
If refrigerant leaks from the radiator, pipelines or connections are detected, restoration procedures such as replacing worn parts, repairing aluminum tubes using argon-arc welding, and replacing seals will be required.
