Lada kalina
Block headlights on Lada Kalina consist of three sections: a passing beam, a driving beam and a side light, a direction indicator. You can replace the lamps with Kalina without removing the block headlight from the car, but for clarity, the progress of work is shown on the dismantled headlight.
Lada kalina
Before changing any of the lamps, disconnect the wire terminal from the negative terminal of the battery.
Replacement of turn signal bulbs
Lada kalina
Turn the direction indicator cartridge counterclockwise by 45 ° … Turn the direction indicator cartridge counterclockwise by 45 ° …
2
… and take it out of the headlamp housing. … and take it out of the headlamp housing.
3
Having pressed a lamp, we turn it against the stop counterclockwise and we take out a lamp from a cartridge. Install the new direction indicator lamp in the reverse order. Having pressed a lamp, we turn it against the stop counterclockwise and we take out a lamp from a cartridge. Install the new direction indicator lamp in the reverse order.
Install the new direction indicator lamp in the reverse order.
Replacement of low beam lamps
four
To replace the low beam lamp, we pull off the protective rubber cover from the body of the headlamp by pulling on one of its three petals. To replace the low beam lamp, we pull off the protective rubber cover from the body of the headlamp by pulling on one of its three petals.
five
Disconnect the wire ends from the lamp terminals. Disconnect the wire ends from the lamp terminals.
6
We disengage the spring clip with two hooks … … and remove it from the lamp. We disengage the spring clip with two hooks … … and remove it from the lamp.
7
We take out the lamp from the body of the headlamp. We take out the lamp from the body of the headlamp.
We install a new passing lamp (H7) in the reverse order.
On a note
In the Lada Kalina block headlights, 55 W halogen low beam lamps of H7 power and H1 halogen high beam lamps of the same power are installed. The direction indicators use orange PY21W lamps with a power of 21 watts. The side light lamp is designated W5W and has a power of 5 watts.
When changing the “halogen”, do not touch the flasks with your fingers, as grease stains will cause the lamps to darken when heated. You can remove contamination from the flask with a clean rag soaked in alcohol.
Replacing high beams
one
To replace the high beam lamp, disconnect the wiring block from the lamp. To replace the high beam lamp, disconnect the wiring block from the lamp.
2
Squeezing the ends of the spring retainer, disengage them from the hooks and remove the latch from the lamp Squeezing the ends of the spring retainer, disengage them from the hooks and disengage the retainer from the lamp
3
We take out the lamp from the body of the headlamp. Install the new high beam lamp (H1) in the reverse order. We take out the lamp from the body of the headlamp. Install the new high beam lamp (H1) in the reverse order.
Replacing the side light bulbs
one
To replace the side light bulb in the headlamp, remove another protective rubber cover similar to the low beam lamp cover and take out the cartridge with the lamp. To replace the side light bulb in the block headlight, remove another protective rubber cover similar to the low beam lamp cover and take out the cartridge with the lamp.
2
We take out the lamp from the cartridge. Install the new side light bulb (W5W) in the reverse order. We take out the lamp from the cartridge. Install the new side light bulb (W5W) in the reverse order.
Replacement glass headlights Lada Kalina
If you want to replace the headlight glass, pry it with a screwdriver …
1–1
… and remove the six spring clips holding the lens to the headlamp seal. … and remove the six spring clips holding the lens to the headlamp seal.
1-2
Remove the glass headlights and glass seal. Install the headlight glass in the reverse order. Remove the glass headlights and glass seal. Install the headlight glass in the reverse order.
Replacing a headlamp Lada Kalina
To remove the headlights, press the tabs …
2–1
… carefully disconnect the wire pads from the connector on the body of the headlamp and bulb holder for the direction indicator. Remove the front bumper. … carefully disconnect the wire pads from the connector on the body of the headlamp and bulb holder for the direction indicator. Remove the front bumper.
2–2
Using a Phillips screwdriver, unscrew the screw of the upper mounting of the headlamp … … and with the wrench or head “8”, three more bolts of fastening the headlamp (shown by arrows) and remove it. Using a Phillips screwdriver, unscrew the screw of the upper mounting of the headlamp … … and with the wrench or head “8”, three more bolts of fastening the headlamp (shown by arrows) and remove it.
2-3
On the body of the right-hand headlamp is marked “RE”, on the body of the left-hand headlamp is “LE”. Install the headlight in the reverse order. On the body of the right-hand headlamp is marked “RE”, on the body of the left-hand headlamp is “LE”. Install the headlight in the reverse order.
Removing the side direction indicator, replacing the lamp
3–1
By moving the side direction indicator towards the front of the car … By moving the side direction indicator towards the front of the car …
3–2
… remove the pointer from the hole in the front wing. … remove the pointer from the hole in the front wing.
3–3
Turning the cartridge with the lamp counterclockwise, take it out of the pointer housing. Turning the cartridge with the lamp counterclockwise, take it out of the pointer housing.
3-4
We take out the lamp and replace it with a new one. Set the side direction indicator in reverse order. We take out the lamp and replace it with a new one. Set the side direction indicator in reverse order.
Checking and replacing spark plugs
(on an 8-valve engine 1.6 VAZ-21114)
4–1
Remove the tip of the high-voltage wire from the candle. Remove dirt around the spark plug. Remove the tip of the high-voltage wire from the candle. Remove dirt around the spark plug.
4–2
With a high “21” head with an extension cord (or a candle key) we turn out a candle A high “21” head with an extension cord (or a candle key) we turn out a candle
4–3
We check with a round probe the gap between the electrodes of the candle. We check with a round probe the gap between the electrodes of the candle.
If the gap does not correspond to the norm (1.0–1.1 mm), gently bend the side electrode, achieving the required value. If the candle is not threaded, there will be a strong resistance to rotation. In this case, it is necessary to completely unscrew the candle and, having cleaned the thread, re-wrap. Finally tighten the candle with a moment of 31–39 N.m. We also replace the remaining candles.
